Reflection of the Day: Removing a Glued-On Wall Mirror

, ,

Please note: I may share links to tools and resources that I’ve used and can confidently recommend, and I may earn from qualifying purchases that you make from links on my site. Rest assured, I will never recommend anything I have not personally used and appreciated.

bathroom basin

I’ve begun demolition on the bathroom, which is the first major step after planning the renovation. My first big demo project is removing a glued mirror covering one entire wall in our bathroom.

Living in a small flat requires lots of tricks to help make the space seem bigger. Using a mirror is a tried-and-true technique that I really like. We added antiqued mirrors to the bespoke shelves that I built in our lounge, and they reflect the light beautifully, creating a sense of more space in the room.

final lounge shelves
Mirrors on the back wall bring some more light into the room.

Each of our two bathrooms, which are quite outdated, feature a huge mirrored wall. While I applaud the technique for making the room look bigger, it is just a bit too much. So I am keen to try removing the glued mirror as part of the renovation. I plan to replace it with a smaller wall-hung mirror that is a bit less enormous.

mirror
This is the mirror I’ve chosen for the guest bath renovation, from Cox and Cox.

Removing a glued mirror of such a huge size feels a bit overwhelming, but after a lot of research, I was ready to tackle it. I am here to tell you, you can do this. But be prepared, it is messy and can be a bit dangerous with many shards of glass created in the process.

removing a glued-on wall mirror
After I removed the mirror, this is the final state of the wall.

The Tools Needed

  • Hammer or rubber mallet
  • Painters’ tape or other tape
  • Chisel
  • Work gloves
  • Safety goggles

A Few Thoughts on the Process

Because I had no idea how to remove the mirror or even how it might be attached to the wall, I did a lot of research. There are a few different recommendations out there for removing a glued mirror, including using shims to wedge behind the mirror and slowly push the mirror away from the wall. When I first read this, I found it hard to believe this could work, but several sources recommended it. Others advocated for covering the mirror in carpet shield, a sticky covering that will hold all the shards of glass in place. But in the end, I decided on a simpler approach with just painter’s tape and a mallet.

Also, this guide will not help you if you want to preserve the mirror for future use. We were not trying to save the glass, and given its size, we needed to break it down just to get it out the door and to the tip.

Let’s get started.

Are You Considering a Bathroom Upgrade?

Get a step-by-step guide and tons of tips and tricks from my own experience renovating my bathroom. From demolition, to water-proofing, tiling, and installing fixtures, this is your ultimate guide through the process.

Ultimate Guide graphic

The Steps for Removing a Glued Mirror

First up, make sure you understand what you are working with, as best you can.

In our situation, the mirror was glued to the wall. There were no clips or screws holding it in place. It also went right to the edges of the wall and ceiling, so there were no options for using the shims method to pry it away. I could not really access the edges.

The edges were caulked with a thick bead of caulk as well.

Once you have a sense of what you are working with, tackle the mirror in small bits.

bathroom
The mirror takes up the entire wall above the toilet, so it is a big project.

Cut the Caulk with a Knife

I first cut the caulk with a knife, to help break the seal. This will help it come away from the wall a bit easier. You can peel the caulk away if you want, just to be able to access the edges a bit easier. But simply cutting it will already help a lot.

Prep the Mirror

Next, I had the idea of cutting the mirror with a glass cutter., to make its size more manageable I cut lines down the length of the mirror and across its width, using a glass cutter and bisecting the mirror into about 12 quadrants. I thought this might help bring it down in smaller pieces. This actually did not work, as the mirror was fairly thick. I might have been able to score the lines a bit deeper, but I think it was a waste of time.

Next, I added painter’s tape, crisscrossing the mirror on diagonals. My thinking here was to help capture big pieces of glass, since I did not know if the mirror might fall in a large piece. I intended for the tape to help capture the pieces, but as I got to work, I actually found it to just be in the way. More on that in a moment.

taping a mirror before breaking it
The tape does not need to be perfect. Just capture the entire mirror with tape.

I really liked the suggestion I found for removing a glued mirror by wrapping it in carpet shield, which is a bit like thick cling film that sticks to the surface. I knew this could help prevent shards of glass, but given the size of the mirror, it felt like it would result in an unwieldy and heavy single piece to have to remove from the room, rather than smaller pieces.

Finally, for removing a glued mirror, I covered the floor with a moving blanket, to help cushion falling glass and prevent too much shattering.

Break the Glass

The next step for removing a glued mirror is the most crucial. You need to shatter the glass so you can start pulling it away from the wall.

The mirror will probably be glued to the wall with large spots of adhesive. By breaking it, you can start to pull pieces away from the adhesive in manageable chunks.

Make sure you are wearing goggles and gloves for this. Preferably gloves specific for working with glass, tile, etc. I purchased these gloves which worked perfectly.

broken wall mirror
When hit with a hammer, the mirror shattered into a series of concentric circles.

I hit the glass a few times, but the mallet just bounced back. Finally, I had my husband make the first break. I was just a bit worried about the right strength to use, and I clearly was not using enough.

You want a solid, concentrated hit somewhere in the middle of the mirror. Do not try and go through the mirror, just a good, solid hit. The glass should shatter, in a spider web of breaks probably in a series of circles radiating away from the spot where the mallet landed. You might need a few different points of contact, depending on the size of your mirror. I needed about four different hits across the wall.

You could use a hammer as well, but if you have a rubber mallet, this might be a bit less violent.

Start Removing Pieces of Mirror

With the mirror shattered, you can now start pulling pieces away from the wall. I used a chisel to help separate the glass from the wall, lightly tapping the broad flat tip up under the crack and then leveraging it away from the wall. The first piece is the hardest, but once you get started, it becomes easier as you have more space for the chisel to get underneath the glass where the pieces of mirror have been removed.

removing a glued-on mirror wall
Making progress with removing a glued mirror

Work in small areas, removing pieces of the mirror carefully. Again, wear your gloves, as there is plenty of opportunity to cut yourself. Eye protection is also important, in case small pieces of glass fly away from the wall.

I started to get into a good rhythm, pulling pieces of glass away and working out from the original breakage point. Because of the size of our mirror wall, I needed to shatter the glass in a few places, and each time, it got a bit easier to make the hit with the mallet.

You will come across blobs of adhesive which will probably be fairly regularly spaced. You can start to anticipate where the adhesive will be as well. In my case, sometimes the adhesive came off with the mirror, and other times, it stayed stuck to the wall. I used the chisel and a paint scraper to pry the adhesive off the wall. It came away fairly easily, but there is some damage to the plasterboard that will need to be repaired.

wall after mirror has been removed
See the blobs of adhesive where the mirror was stuck to the wall.

I did not find the painter’s tape to be that helpful. It actually just got in the way as I pulled pieces of mirror from the wall. The mirror came down in manageable pieces, so there was no need for holding it together, which the tape was meant to do. But if in doubt, I would still use the tape, just in case. It certainly does not hurt.

Dispose of the Mirror

The removal of a glued mirror goes fairly quickly. I was able to remove our full mirror wall in less than two hours, working slowly and methodically. I was super careful of the shards of mirror, so I went slower than I probably needed to.

Once you have all of the mirror removed, you need to dispose of the glass. In our case, there was a lot! I had a few really big pieces, but mostly, there were lots of small pieces, and even more tiny slivers.

In my case, I assembled two moving boxes and lined the bottom with a plastic rubbish bag, just to keep the glass from slipping through. I taped them really well, to be able to withstand the weight. Then, I carefully stacked the pieces of mirror in the two boxes. I needed to break a few large pieces even further down to fit. And I brushed all the shards and small bits into the boxes as well. We put these on a little hand truck and got them to the car and to the tip without incident.

Be super careful. Even the gloves may not protect from very jagged edges if your hand hits them just right. Ask me how I know this …

Then sweep, vacuum, sweep, vacuum, and do it again. Then again. And then yet again. There is a lot of glass, and I had many tiny slivers. To ensure they did not get into the rest of the house, I kept the door closed during work, and again, I vacuumed and swept many, many times. I even ran a wet mop over the room after, to catch any microscopic particles.

The Pros and Cons of My Method of Removing a Glued Mirror

Overall, I am really pleased with my approach. As noted earlier, the shims would not work since my mirror went straight yp to the surrounding walls and ceiling, with no space for sliding shims in place. And while I like the idea of using carpet shield, I think it would have made this huge mirror quite hard to work with.

My method, with painter’s tape, a mallet and a chisel works brilliantly. The mirror came off the wall in manageable pieces, and it was fairly quick work. Quicker than I expected. And damage to the wall is minimal. I’ll need to do some patching and sanding, but overall, it is not too bad.

The one drawback is the amount of glass shards. There were bits of glass everywhere. Clean-up actually took longer than removal, to make sure I captured everything. The carpet shield method would prevent all the glass shards, but again, I am not sure it would be that easy on such a large mirror.

Overall, besides the clean-up, I found my approach worked really well. That is likely the approach I will take when I renovate our second bathroom, which will require removing a glued mirror again.

Next Up: Removing the Tile and Fixtures

With removal of the glued-on wall mirror completed, it is time for the next steps in the demolition: removing tile and bathroom fixtures. Join me next week for some tips and tricks for removing tile. And in the meantime, let me know your thoughts on removing a glued-on wall mirror. Would you tackle this project yourself? It was certainly easier than I expected!

Happy DIY-ing!

I’m not an expert. I’m an intrepid DIY-er who believes skills are learned, not innate. If I can do this, so can you. What will you build next?

Stacey profile picture

Stacey

/

Intrepid DIY-er



Leave a Reply

Your email address will not be published. Required fields are marked *

Looking for inspiration? Follow me on Pinterest